Close

미니크아 게임하기 크레이지 아케이드 플래시게임

지플레이메카플래시게임45 Comments

미니크아 크레이지 아케이드 플래시게임

이 게임을 평가해 주세요!
평점 5 / 5점 · 참여 1

미니크아 크레이지 아케이드 게임 소개

넥슨코리아 BNB에서 제작한 미니크아 게임은 물풍선을 활용해 벽을 파괴하고 적을 공격해 악당 로두매니를 물리치는 목표를 가지고 있습니다. 게임 조작 방법은 간단하지만 다양한 몬스터들의 등장으로 인해 난이도는 점점 높아집니다. 플레이어는 배찌를 이용해 벽을 깨뜨리고 아이템을 획득하며 파워업을 통해 더욱 강력한 공격을 시도해 볼 수 있습니다. 로두매니의 움직임을 예측하고 물줄기를 맞춰 승리하는 방식입니다. 게임 과정에서는 미라나 박쥐와 같은 몬스터가 등장하는데 이들과 접촉을 피하는 것이 무엇보다 중요합니다.

조작키 설명

이동(방향키) / 물풍선(스페이스바) / 아이템(1 ~ 3)

플레이 스크린샷

미니크아 다운로드 링크

플래시게임(SWF) 다운로드

크레이지아케이드 사이트 바로가기

공식 홈페이지

댓글 45

  18. with the Balanset-1A Device

    Equipment Preparation

    accelerometers, laser rpm sensor, mounting stand, software application, and additional tools.
    Connect the device to your PC using the USB interface and confirm the software installation.

    Mounting the Sensors

    Mount the vibration transducers securely on the machine’s housing where vibrations are most pronounced, typically near the bearings.
    Direct the laser speed sensor towards the rotor and affix reflective tape to the rotor surface to facilitate phase angle measurement.

    Starting the Program

    Launch the Balanset software on your computer.
    Configure the software for either single-plane or two-plane balancing, based on the rotor’s characteristics and the desired outcome.

    Measuring Initial Vibration

    Bring the rotor to its normal operating rotational frequency.
    The software will measure the vibration level, rotational speed, and phase angle. This data establishes the current imbalance condition.

    Trial Weight Installation

    Halt the rotation and mount a test weight at a designated position on the rotor, with the weight’s value entered into the software (usually in grams).
    Restart the rotor, and the software will record the changes in vibration level and phase angle.

    Computing the Compensating Weight

    The software uses the measured values to automatically compute the necessary compensating weight’s magnitude and placement angle.
    These parameters are displayed on the screen as numerical data and graphs.

    Installing the Correction Weight

    Mount the calculated corrective weight onto the rotor at the specified location and angle.
    You can conduct interim measurements to confirm that the imbalance is decreasing as expected.

    Final Check and Balance Confirmation

    After installing the correction weight, run the rotor again and check the residual vibration level.
    The balancing procedure is finished if the remaining vibration is within the permissible limits specified in ISO 1940.
    Should the vibration still be excessive, repeat the balancing steps, making further adjustments to the corrective weight as needed.

    Report Generation

    All balancing results are logged and archived within the software, from which you can produce a printable report summarizing the vibration levels, compensating weight, and its installation position.

    Concluding Steps and Verification

    Ensure all applied weights and attached sensors are firmly fixed in their designated positions.
    Check that the rotor’s rotation is smooth and free from undue noise or vibration.
    If the rotor operates within a larger assembly, check the functionality and interplay of all interconnected parts.

    Following this procedure enables accurate balancing, minimizes vibration, and prolongs the service life of the equipment.

    Instagram: https://www.instagram.com/vibromera_ou/
    Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL
    Our website about Balancing of refrigeration compressors
    Machinio: https://www.machinio.com/listings/98380186-portable-balancer-vibration-analyzer-balanset-1a-full-kit-in-portugal
    Facebook: https://www.facebook.com/marketplace/item/350151228150722

    Reply

댓글 남기기

Copyright © 지플레이메카